You know the sound. Drip. Drip. Drip. Easy to tune out at first, harder to ignore once you actually do the math on what it's costing you every month. Here's the good news: a leaking bathtub faucet is one of the more fixable plumbing problems you'll run into. Most of the time, you don't need to call anyone. You just need to know what's actually causing it.
What's Actually Causing the Drip
Before you touch a single screw, it helps to know what you're dealing with. A handful of things cause almost every bathtub faucet leak out there:
- A worn washer. They compress with use, over and over, until one day they just stop sealing.
- A damaged cartridge. If your faucet runs on a cartridge instead of a washer, normal wear is usually the whole story.
- A corroded valve seat. Hard water leaves mineral deposits behind, and eventually that corrosion causes dripping even in otherwise fine hardware.
- Loose parts. Nuts, screws, seals — years of use and they just work themselves loose. Happens to everything eventually.
What You'll Actually Need
- Adjustable wrench
- Flathead and Phillips screwdrivers
- Replacement parts — washer, cartridge, or O-rings, matched to your exact faucet
- Plumber's grease
- A bucket or towel for the water still sitting in the line
Fixing It: Step by Step
1. Shut Off the Water First
Non-negotiable, this one. Find your shutoff valve or the main supply and close it before you touch anything else. Then turn the faucet handle to drain out whatever's left in the line. Skip this, and you'll regret it almost immediately.
2. Pull Off the Handle
Screwdriver, counterclockwise, handle comes off. If there's a decorative cap hiding the screw, pry it off gently with a flathead first. Keep every tiny screw and part somewhere you won't lose it — a small dish on the counter does the job.
3. Take a Real Look Underneath
Once the handle's off, actually look at what's there. Minor grime on the stem or cartridge? You can usually clean that yourself. Serious rust or corrosion? That's your sign something needs replacing, not cleaning. In an older faucet, honestly, a worn washer is usually the actual answer here.
4. Pull the Cartridge or Stem
Loosen the retaining nut with the wrench and pull it out. Check it for cracks, rust, and any real wear. If it looks even a little questionable, that's the part to swap.
5. Swap the Worn Parts
Replace whatever looked bad — washer, O-ring, cartridge. Get the size and shape of the washer exactly right; a slightly wrong replacement is one of the most common reasons people "fix" this and end up leaking again two weeks later. A thin layer of plumber's grease on the new parts before you fit them back in.
6. Put It Back Together
Stem or cartridge back in, retaining nut locked down, handle screwed back in place. Check the handle doesn't wobble and sits properly before you call this step finished.
7. Test It
Water back on, watch closely. Still dripping? Go back and recheck your seals — something didn't seat right the first time. Still going after a careful second pass? That's genuinely the point to call a plumber instead of guessing a third time.
Keeping It From Coming Back
- Check it once a year. Catch the wear before it turns into a drip, not after.
- Don't muscle the handle shut. Cranking it harder than necessary every single time wears down washers way faster than it needs to.
- Hard water? Look at a softener. That mineral buildup is exactly what corrodes valve seats over time, so softening it genuinely extends how long your faucet's internals last.
- Due for a new faucet anyway? Consider low-flow. Different thing from a softener — this cuts the volume of water moving through, which helps your bill and reduces wear at the same time.
When It's Time to Call Someone
If the leak's still there after an honest repair attempt, or the faucet feels like it's failing structurally rather than just worn out, stop and call a plumber. Some issues go past a washer swap, and there's no shame in that.
Frequently Asked Questions
How do I know if it's the washer?
If the drip starts the second you turn the handle off, that's the classic washer tell. Pretty reliable sign.
Can I skip shutting off the water?
No. Don't. You'll be fighting an active leak the whole time you're trying to work, and it's a mess nobody needs.
How often should I actually check this?
Once a year is plenty. Enough to catch early wear before it becomes a problem you're writing a blog post about at midnight.
Final Thoughts
A dripping bathtub faucet doesn't have to be some ongoing mystery you just live with. Right tools, about half an hour, and most people can handle this themselves. Catch it early, and you save water, save money, and skip the slow water damage that gets expensive fast if it's left alone.
Drain running slow too? Our guide on how to unclog a bathtub drain covers that. And if the faucet's actually due for full replacement rather than a repair, see how to remove an old bathtub faucet to get started.